Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
hi we have designed a board with nrf52840 with nrf21540.and we have designed it to communicate it with spi .Is the spi example for nrf21540 is available in sdk . if not where...
Env:
gcc version 10.3.1 20210824 (release) (GNU Arm Embedded Toolchain 10.3-2021.10)
std=c++11
nRF Connect SDK v2.0.0
Including nrf_socket.h from nrfxlib/nrf_modem...
Hi,
I am using BL653dvk, which has nRF52833 as soc. I am working on DFU-OTA example by following this link.
https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0...
I tried to build hci_spi example application for nrf5340...
identifier "__device_dts_ord___BUS_ORD" is undefined
identifier "__device_dts_ord___P_irq_gpios_IDX_0_PH_ORD...
While migrating my project to use the new pinctrl mechanism in I ran into an issue where the I2C communication on some busses was not working. Further investigation revealed...
Nordic Connect SDK 2.0.0 moved to the use pin control interface, also for I2C.
When I tried to port some of my application I noticed a possible regression.
As a basis...
According the BLE specification, the software and firmware revision strings are mandatory. I would like to set put information about the softdevice version in the firmware...
I'm trying to make a one-shot mqtt function. The process is below
- connect - publish - disconnect
Then I coded like below. I show only the core code.
Do I have to...
Hi,
I want to get a sample that supports both BLE OTA and NUS functions, so I find the following two samples as reference and merge them together.
...\zephyr\samples\subsys...
Nordic BLE Mesh transmission is transmitted through the Publish address bound to the model in the Instance, so that subscribers can receive packets.
As shown in the figure...
Project: Variation of Nordic ble_peripheral project
SDK: 15.1, Softdevice : 132 rev 6.1
How do you change the BLE packet length? I have a project where I defined a characteristic...
I am using the example zephyr basic button which gives output when the button is pressed.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/zephyr/samples/basic...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
we currently have a product which use nrf52832 as processor using SD132 for BLE capability with DFU capability
we want to build a sister product with nrf552810 with no SD...
HI,
We are looking to multiplex a few I/O on the NRF52840 to save pin count on a header. If D+ or D- get driven when VBUS is unpowered, will that damage the NRF52840? Or...
