Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I'm trying to run some example with ble fota
I've read
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52.html#fota-upgrades
and
http:/...
Hi i am using nordic nrf52840 chip.
i programmed one application at 0x27000 address, and now i want to calculate the size of that application code in run time.
i have...
Hi
I have a project as the follow
What I have done:
1. Compiled app.hex ( Configured with my board), works fine.
2. Compiled bootloader.hex ( Configured with my...
Hi, I've adopted the DFU part of the NRF Toolbox app in my own app. I want my app to be bi-langual (English / Polsih). I can do this for all the texts that I've created, however...
Hi,
I had a temperature adc reading accuracy issue in lower temperature such as -40.
It is similar to this post issue ( https://devzone.nordicsemi.com/f/nordic-q-a/80859...
Hello,
My application is built with TFM in order to use mbedtls. I am currently using UART0 to send/recv serial data from another board. If I don't call psa_ps_get_info...
Hi,
We have developed one application using nRF52832 SoC and Sdk v15.0. For our application we have use ble_app_uart example as a peripheral and multi-link central example...
Hi,
I am using s112_nrf52_7.2.0_softdevice with nRF5_SDK_17.1.0 and iar embedded workbench. I can flash and run the application without any problem but when i try to program...
Hello Devzone,
I am trying to run timeslotted 802.15.4 alongside BLE using NCS. I have started from this example, replacing the propiertary RF calls with calls to 802...
I was able to set up 2 thingy91's using the nRF9160DK to update the firmware and the asset tracker is working on the 2 thingy91's. I've tried to provision the DK and I get...
Hi,
I am trying to port the nRF5_SDK_17.0.2_d674dde\examples\nfc\writable_ndef_msg and my linker cant find the definition for the following symbols-
linking... .\_build...
Good afternoon ladies and gentlemen,
Just a really quick question/observation... am I going bonkers? or is the link to Segger Embedded Studio on this Nordic Page incorrect...
Hi nordic:
I use nrf9160 to test the new driver mainly due to the following two problems:
Environment: sdk 1.8.0-rc2 modem: nrf9160_1.3.1 lwm2m CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hi There,
I have a question now. If I want to alter the frame format in the data linker, how do I do?
I try to find the source code of the data linker layer in the Mesh...
