Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello everyone,
I'm currently working on porting a device driver to Zephyr on the nRF9160. I have defined a device tree and set up the device through the .overlay file...
Hi
I was wondering if there is any further reading about the Automatic network selection set as <mode> in the +COPS set command.
Especially, I'm looking for a solution...
Hi,
I just recently began implementing the mesh stack into an existing application, using mesh v3.2 and nrf sdk 15.2.
Integration works well by using the integration guide...
I am currently working on nRF52DK and TCAN4550 using SPI communication. Regardless the SPI slave which I am using, I have some doubts with SPI Nordic library (I am using 17...
Hello,
I have been trying to configure the c_cpp_properties.json file of Visual Studio Code so that I can edit my project from there, but I can't seem to find the preprocessor...
It appears that the DFU bootloader has been overwritten/damaged on nRF52840 Dongle as it no longer resets (the red flashing led does not show) when I hit the RESET button...
HI,
I wanted to know what is the default tx power set level in S130, I took a example from sdk 11.0.0, (ble Peripheral/ble_app_uart) but i dont see anywhere this example...
I struggled for a while with this: the SDK documentation and the example application did not explain a common use case: reading and writing single-byte registers in a peripheral...
I need to measure periods with high precision, so I need to make sure that the HF clock is using the external XTAL; when the softdevice is not started (for testing mode) I...
Hello,
I am building a wireless sensor network for my coffee business, I am using a raspberry pi as the gateway with nrf24l01 connected to it, I have a bunch of sensor nodes...
HI
I have followed the below-mentioned tutorial
https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0#h117sk6474thpzmbdphj6gan2vw7rzj...
PCB above my collection of audio data by codec, and then through the Bluetooth upload, the audio signal noise will be ticking ticking, may I ask what is the reason
hi, all
I added scan module at 'ble_app_uart' example..
Error in function nus_c_init. (0x08)
So when I follow the line by line, it seems that the 'registered_handler_set...
Hi,
Iam using Segger Embedded Studio (SES) v5.20, SDKv17.0.2, NRF52840 DK board, NRF52810 Microcontroller in the Custom Board
Since we don't have the PCA10040e folder...
