I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Dear Sir,
Moving to zephyr new installation 1.4.99
Configure SPI1,SPI3 . I can see the SPI configured in zephyr.dts
spi3: spi@b000 { #address-cells = < 0x1 >; #size...
Hi,
I am using the stts751 temp sensor with nrf52832 for temp data logging for short time. I want to save temp data in the internal flash memory but I didn't find any similar...
I followed the instructions in https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.3.0%2Fsdk_config.html
and pasted the appropriate text...
Hello,
I have been trying to get the ADC working but for some reason, the adc_read function throws an error of invalid argument ( -EINVAL (-22) ). The adc_channel_setup...
Hi all, I have tried to follow the step to get up and running with my new nRF9160-DK, however, I am not sure if the Application FW has been successfully updated (how would...
Hi,
We are using a bootloader/DFU based on the secure_bootloader example with USB transport from SDK15 and It works fine.
Now, we are trying to add the possibility to...
hi.
i use nrf52840 to d evelop a keyboard .i connect and be bonded by a pc,now i want to delect to the bond info of the pc,and after this ,my adv cant be scan by this pc...
Hi Nordic Tech Support team,
One of my customers is having some problem with UARTE implementation. They used the ble_app_uart example ( pca10056 with SoftDevice 113 )...
Hello Everyone,
We are developing one custom device using open thread protocol.
We are using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 and Dev-kit - nRF52840...
IN Establishing the friendship,I received the following error
/** The Low Power node was not able to send transport command due to internal fault. */ NRF_MESH_EVT_FRIENDSHIP_TERMINATED_REASON_INTERNAL_TX_FAILED...
I want to send ADC data over bluetooth. When I searched, I found the following contents.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fble_data_throughput...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
