Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
We are currently developing a Zigbee network based on nRF52840.
One of our devices was specially designed to contain 8 endpoints. But when an active ep request is...
Hi,
I'm using the BLE_app_interactive example as a starting point for my prototype (with SDK_17.0.2 and SoftDevice s132 ). I am using nRF52DK to read and write data from...
Hi
Im trying connect two peripheral devices through UART
The example project I used is "examples/peripheral/uart"
But i trace the code, it seems that the driver layer...
Hello,
I've been using nrfx UARTE driver on the nrf5 15.2.0 SDK on a nrf52832 and nrf52840 SoC and noticed that during the boot-up the first byte being sent is 0xFF.
Is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
I'm trying to get LPCOMP working in Zephyr.
I'm getting the following error:
error: 'NRFX_LPCOMP_DEFAULT_CONFIG' undeclared (first use in this function)
I can see that...
Hi, Can anyone explain what the "receiver address correlation" from 2.4GHz Radio documentation means in practice? For example, what can I do as a BLE application developer...
For various reasons we need to remove the dfu bootloader to use our custom bootloader. We replace the Nordic bootloader with a temporary one that does the clean-up for us...
Hi,
We're designing a PCB for the nRF52833. We could not find a PCB layout recommendation for the chip.
We did find one for the highly similar nRF52840: github.com/.....
Hi,
We want to buy a nrf5340 module but it came with the Rev C Silicon Revision. Do you have any errata sheet for this revision? I only find Rev A, D and 1 on your web...
Hi - I noticed an issue in the esb library as of nRF5 SDK v17.0.2 and am looking for clarification.
In the function update_radio_bitrate , the minimum retransmission delay...
Hi Nordic Forum,
I am making a media control device using the nRF52840 and nRF5 SDK. I started with the ble_peripheral\ble_app_hids_keyboard but I don't know what is the...
We use nRF52832 and SDK 17.0.2 and the buttonless secure bootloader without bonding. I don’t understand the below issue, does that apply to our solution ? There will be custom...
