I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello,
nRF51822
SDKv11
Kail 5.18
SD130
I have a pcb that has a sensor with I2C. I made a project that based on the sample of "twi_sensor", and I can read the sensor...
Hi all, I am trying to build the beaconing example from the nRF5 SDK for Mesh. When running:
$ ninja flash_beaconing_nrf52832_xxAA_s132_6.0.0
I get the following error...
I have 3 nRF52840 dongles and want to setup a mesh network between them. Which example from the SDK should I execute and how will i come to know if its working fine.
Hello all!
I'm using a nRF52 DK, which has been already programmed with the soft device s212, since my interest is to be able to connect to sensors using ANT+.
My purpose...
Hi,
We are currently testing DRX (not eDRX) on our custom board, and we would like to reduce the power consumption.
When everything on the board is in low power mode,...
Hi Goature,
We are also try to implement the same. We aren't getting any idea how to start. Refer the same thread : devzone.nordicsemi.com/.../make-ble-central-send-firmware...
Hi there,
Is there any Zigbee Motion Sensor code example that someone has put together? I could not find any on the nRF5 SDK for Thread and Zigbee.
Thanks
Hello,
Was programming two different boards today with the new 1.1.0 modem firmware.
Programmer reported the following for the two boards.
2019-11-21T21:10:34.297Z...
Hello!
Some time ago you seem to bundle sample 5 x nRF52832 to nRF52DK. Recently there was no bundled chips. Why did you change that?
The development and prototyping...
Hello, I tried to set up my nRF9160 with this tutorial and there is a problem: https://www.youtube.com/watch?v=jZQcmU3KIMY&t=216s
According to the tutorial, LED 3 and the...
I'm investigating the PDM peripheral on the nRF52840 and I have not been able to find out what the RATIO configuration bit actually does.
Presumably it controls how aggressive...
Hello,
I try to solve one problem with SYSTEM OFF and I still have no idea.
In my device I have one button switch and with this button I need to change characteristic...
I am using nrf52832 modules connected in mesh light switch example configuration from mesh V 3.2.0 i am unable to send a array over mesh i have gone through various posts...
I wanna know that, is latest SDK has demo example which will convert nRF52 SoC
to act like basic 2.4 Ghz transceiver (who should by default remain in Receiver mode &
switch...
Hi guys,
My question is really general: How do I reduce the TX Power of an nrf51822 BLE beacon?
The situation is the following:
1. I ordered this device: https://www...
