HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
I am using VSCode with the nRF Connect extension (latest) and SDK 2.9.1.
I made my new app from the Bluetooth Peripheral sample.
When I try to debug I get the following...
I am using VSCode with nRF Connect extension with the 2.9.1 SDK.
I am trying to write my own device driver for the Zephyr OS and the TI CC1101 chip. Since the tutorial isn...
Hi,
nRF52832, SDK 17.1.0 with Softdevice S132.
Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
Hello,
I use a PKK2 for power measurements on a nRF9160DK and Feather nRF9160 from circuit dojo. With the UDP example to test it out the sleep current so I can determine...
Hi Sigurd,
I'm finally using the mcuboot and mcumgr_cli I worked on in summer of 2023. I generated the mcumgr_cli for debian with go lang back then. I'm building my app...
Hi Nordic team,
We are currently investigating how to ensure that the fuel gauge continues learning and retaining the battery's charge/discharge profile over time.
In...
I am using Zephyr 2.9.0 with the sdk-nrf repo v2.9-branch checked out. The locator_tag sample builds without issue and flashes to the nRF54L15-PDK without issue. I have a...
I'm trying to use raw packet transmission (IN combination with wifi promiscous mode and raw sockets eventually) with my nRF WiFi device. I have both the sample raw_tx_packet...
Dear DevZone,
I would appreciate your assistance in understanding how to correctly configure Wi-Fi and BLE coexistence for the nRF5340DK and nRF7002EK with SDK version 2...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
