It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
How to select different Advertisement types ADV_IND/ ADV_DIRECT_IND/ ADV_SCAN_IND...
I have my nRF91 DK connected to nRFCloud, thanks for making that super easy! I'd like to review any debug data and learn more about the nRF91 which is new to mean but when...
Hello there,
We are a test lab based in Leatherhead UK, and would like to use your nRF52840-DK for setting up a test jig to communicate with a DUT(Device Under Test) ...
Hello,
I am trying to determine whether or not the SPI EasyDMA functionality of the nrf52840 supports double buffering in the sense that the DMA controller will switch buffers...
Hello, I have a problem with properly adding the Azure IoT SDK (C) into Segger IDE. Anyone already managed to get through that? My goal is to have Azure IoT Hub working with...
Hi, I'm attempting to use the nRF52832 Smart Remote 3 SDK for a project on an nRF52832. I wish to add Serial Output capability (for debugging purposes). I followed the example...
Hi,
I notice that inside the MESH SDK, "Friend" is actual a hex file from zephyr, which I cannot modify. My goal is to set a "Friend" to connect more than 1 LPN (low power...
Hello, community. I have a question about hardware and software setting for using 32Mhz.
(1) Software setting in sdk_config.h
#ifndef CLOCK_ENABLED #define CLOCK_ENABLED...
Hi, I'm searching a example project to do the qualifications test for my product. I'm using SDK 10, have you an example for this SDK? (in your site I found an example with...
Hello
I'm trying to maximize the throughput between a NRF52832 and iOS devices in both directions.
Currently, I seem to achieve about 400 Kbps from an iPhone 8 to the...
Hello, I Have been using your app Connection for Mobile to test my Heart Rate Monitor BLE, I am using also an Honor 9 Lite (Lineage OS 15.1).
The app Nrf find my monitor...
I would like to use the beacon example to send some manufacturer specific data over BLE.
I am using the nrf52DK , nRF5_SDK_14.2.0_17b948a and s132.
My question is other...
What's the fastest scanning settings for connecting to anywhere from 1 to 20 peripherals at a time? My peripherals are all advertising at 211.25ms. I won't be sending any...
Hi,
I am trying to use an SAADC converter to measure voltage in range from 0v to 3v5 but I cannot succeed. It is not possible to measure a voltage above 3V1. Well at least...
Hello, community.
I'm using NRF51822 SoC(256KB ROM, 32KB RAM) with S130 Softdevice.
I'd like to reduce the rom size and the ram size to decrease the production cost. ...
