Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Using the 15.2 SDK, the stack generates an error when attempting to bond. I am using the android nRF Connect test app to initiate the bonding after connection. The error generated...
I'm using SDK 15.2 & HID keyboard example. I would like to know the following things-
1. How long does BLE chip advertise its name before making a connection with central...
Hello,
We're currently preparing for BLE certification of our device. It contains an NRF52840 on a custom PCB, so I believe we'll need to perform RF-PHY testing for certification...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi! I develop board based on NRF52832. P0.08 is connected to the MOSFET transistor.
The transistor switches the relay. During start (power on or reset) on GPIO there is...
Hello,
Please let me check about the usage of an IRK for the default setting and how to change an IRK each bonding cycle.
We use the resolvable address for our application...
Hello
I have a setup with 3 nrf6310 dev kit and with a nrf24LE1 module on each of them.
1 acts as a transmitter and the other 2 act as a receivers. What I specifically...
Hi
I am using nrf52 DevKit and was able to load the \examples\ble_peripheral\ble_app_beacon program on it. I am able to see the beacon RSSI, major and minor values. Now...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832
I am trying to implement Normal DFU in Mesh network.I don't need Mesh DFU.
So i have added...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I am bit confused between fds_record_update...
Hello, I am using AES -CCM encryption in my program. I want to know about memory like does it need any dynamic RAM ? In example code I found 'nrf_mem_init()' but unable to...
Using: NRF52832, SD 132 6.1.1, SDK 15.3.0, Mesh SDK 3.1.0.
Hi, I included mesh_opt_core.h in a C++ file, and got compiler errors at NRF_MESH_STATIC_ASSERT().
I fixed...
Did current OTA only can dmostrate "ble_app_hrs" and "ble_app_rscs"? Other SDK5.0.0 examples?
I want to try ble HID keyboard. So, deliver the hex file to celluar phone and...
