Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
I want to use nRF52840 BLE with STM32F745ZG microcontroller and using atollic studio for coding. is it possible to use nRF52840 with the microcontroller? if it is possible...
I'm using SDK 15.1, nRF52 in custom units, toolchain GDB, addr2line
A little background -
We use System off mode and then use a button press to come out of it.
Before...
After doing a detailed review for the datasheet for nF51822, I can find no input leakage current specification for the digital inputs or ADC inputs. Where do I find this specification...
Hello,
for current consumption measurement of our PCBs, I created a special software. This software does boot up, puts SPI FLASH in power down and go to sleep forever. All...
Hi, Sir:
I am using nRF9160 for development, I would like to complete a COAP client,so I need to refer to ......./nrf/samples/nrf9160/coap_client. I installed NRF_Connect_SDK...
Hello, LTE-M modem firmware version 0.6.8-131.prealpha released which have a big advance.
Did the NB-IoT modem firmware which aligned to LTE-M 0.6.8-131 released?
Which...
Hi i am using ble_app_uart example in sdk 15.3.0 as far everything is fine even i added a app_timer for about 20 sec to advertise again but the problem is when i power up...
I'm trying to use the new ble_advertising_advdata_update from SDK 15.1 by doing
but I get NRF_ERROR_INVALID_ADDR
What do I need to do to get it to work?
Hello,
I use an nRF52840 that I program with Segger Embedded Studio. I am using J-Link driver version 6.44f.
When I want to connect to J-Link I get the following message...
Hi, all! After updating all libs can't flash. Have this error: Tested also with asset_tracker sample. Using runner: nrfjprog nrfjprog --ids Flashing file: /home/ilya/projects...
Hello Dear support,
Please help me with the error. I understand from the documentation that 0x11 err_code for nrf_drv_twi_tx() means invalid data. But I dont understand...
