It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
I work on your new Mesh SDK 3.1.0 and I have some questions for you.
First it is about DFU over Mesh. I think your documentation is very weak. I understand that they are...
Hello Nordic, we use the nrf52 proprietary protocol in the project, it will send 200 data per second, and no ack confirmation, the application data length is 25 or 32 bytes...
SDK 15.2
Segger Embedded Studio Release 4.12 with DEBUG on
Segger Ozone V2.60k
FreeRTOS 10 from SDK (same issue with FreeRTOS 10.1.0 source files and original ported...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
Hi,
I have a project which need to use two UART interface at the same time.
As well known, there only have one hardware UART interface in nRF51822/nRF52832. If I want...
Hello, DevZone,
I have programmed an nRF52-DK with the unmodified SDK's ble_app_hrs_pca10040_s132 (heart rate monitor) BLE peripheral application. I also have a Power Profiling...
Hi Susheel,
Thank you for your support.
We would like to get your advice related our new design, with the followings:
Assume we need to support besides of the BT5...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
