Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
HI,the current situation is that nrf52832 can not receive the ack_payload from the nrf24le.
nrf52832 as DEVICE,using the project NRF5_SDK_13.0.0\examples\multiprotocol\experimental_ble_app_gzll...
I am a beginner and I need to know how we can further modify the light switch example codes to access gpio pins and get some output from that.
I have run the example using...
