Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
I am trying to debug my code in Eclipse using J-Link.
Whenever the code executes vPortStartFirstTask() in vTaskStartScheduler() the debugger stops and I can't debug...
Hi,
is there any simple way to obtain current PWM value if nrf52 PWM module is used to produce complex waveform from RAM array? The task is to get currently settled value...
Hi there,
I am new with nRF52 using SD332 and ANT+. I would like to ask if the nrF52 with SD332 can be configured as ANT+ central and ANT+ peripheral in the same time....
I have a query that is similar to the question below
https://devzone.nordicsemi.com/question/44424/how-do-i-switch-the-target-from-a-nrf51422_xxac-to-nrf51422_xxab-in-keil...
Hi,
We are currently considering the packaging design of a device which will use a nRF52. During housing assembly, the populated, but unpowered, PCB will be exposed to...
Hello.
I have a question.
I use nRF52 and S132v2. I found some programs of nRF51, they use S110, S130. What change does it with difference of Softdevice's version number...
Hi,I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master and tested it on NRF52(PCA10040) development board it advertising Eddystone-URL frame successfully and...
hi
i have nrf51422 v2 that use sdk v6 and s210 v3
when i download an example on my nrf and run it to see error check its not returning anything
in s110 i have error...
Hi, In my custom project I need to add two 128-bit uuid services and also I need to use pstorage to protect the application data from power loss. But I got the problem is...
Hi,
While working on OTA DFU using my custom code compiled to work on PCA10028 board, I am seeing the following issue.
The OTA DFU works fine using Master Control Panel...
Hi,
I'm designing an antenna for the NRF52 but with some different conditions, the antenna will be under a silicone superstrate and this will change the impedance of the...
Hi..
Everyone,
i am using nrf52 with softdevice 132.
i used peer manager.
i am able to able to flash softdevice, bootloader and application.
but after that application...
Hi,
I've built a device using an IMUduino board, which is supposed to be similar to Arduino Leonardo board with a nRF8001 bluetooth. I was able to connect my device to...
Hi all ...
My product uses multiple BLE peripherals (Simblee by RF Digital) communicating with a common BLE central to time events detected via sensors on the different...
