I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
The docu page for the nRF9151
https://docs.nordicsemi.com/bundle/ps_nrf9151/page/ip/radio_lte/doc/frontpage.html
contains a link to
docs.nordicsemi.com/.../intro_nrf9160...
I have customed my own 52820 dongle board.
I wanted to run ncs2.7.0/zephyr/samples/subsys/usb/cdc_acm demo on my board to test whether it worked. So, I builit the cdc_acm...
Hi
I'm trying to make the UART-HCI example run on my nRF5340-DK board.
Environment: - nRF5340-DK Version 2.0.0 (2022.13) - nRFConnect 2.7.0
I've built the example with...
Hi All.
A few years ago, Nordic documentation for developers included many "examples" to practice with and learn about this technology. For instance, ... >examples>ble peripheral...
Hello,
I am in the process of adding LPN nodes to my network, Unfortunately I am getting a lot of "Ignoring old SeqAuth" Warnings and looking at the LPN friendship call...
Hi
i bound rtc in nrf52833 and set/get the time.
but the time is not incrementing ,iam reading the same time which i set.
i added the config below,
but no change in...
Hello,
I am trying to configure P0.9 as output and toggle this pin.
It is no possible but if I change the number of the pin then I can see the modification of the output...
I ran this exercise a month or two ago and it worked to do OTA updates. I then tried recently again and it is giving me "Device not supported" in the Nordic Device manager...
How can I get the lis2dh12 accelerometer speed at 1.344 kHz as mentioned in the datasheet from thingy52?
I have configured the registers as per datasheet of the accelerator...
I tried running the official ranging example with nrf5340dk.
Bluetooth: nRF Distance Measurement with Bluetooth LE discovery
Usage
This example can obtain distance test...
