Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I’m currently developing an application for the nRF52833 that collects sensor data via SPI and sends it out over BLE using notifications. My primary goal is to achieve...
Hi,
I am trying to create a device two temperature measurements.
I have created two endpoints like this:
but when I try and compile, I get this error:
G:/ncs/v2...
Hello! I am trying to monitor mbedtls heap usage in the azure_iot_hub sample (v2.8.0), building for nrf7002dk/nrf5340/cpuapp/ns. I can see in modules/crypto/mbedtls/library...
I am trying to enable userspace for my project. I am getting this error on one of the last steps related to some debug info.
I can compile fine with all the same configs...
"I added an endpoint called Matter Extended Color Light to the matter_bulb example. After compiling and flashing the firmware, HomeKit only recognizes and creates two dimmable...
Hi,
I want to connect LDC2114 to nRF9160. I write the nrf9160dk_nrf9160_ns.overlay and the astri,ldc2114.yaml. I don't know how to set GPIOs in & i2c1 - ldc2114: ldc2114...
Hi all,
I am dealing with a similar problem to this post: https://devzone.nordicsemi.com/f/nordic-q-a/110715/creating-development-env-for-nzrzf5340-error-warning-nrfjprog...
Hello,
I am using the nRF54L15-DK and nRF Connect SDK v2.8.0, and when I try to compile the Zigbee Coordinator sample, I get an error saying that <zboss_api.h> cannot be...
I'm using NCS version 2.6.1 with a NRF9161DK
Recreating the issue:
Follow the instructions in the readme of the sample: Cellular: nRF Cloud multi-service
Build with...
Hi nRF experts.
We are RF module manufacturer, We are developing nRF54L15d module, When we develop production test software, we need to test power off current, Using the...
I'm trying to get a gas gauge and charger IC to work on the i2c bus. Both have different addresses. I'm able to read from the gas gauge address but not the IC. Are there specific...
Hi Nordic:
I use NRF54L15 for my product and hope to use ANT+AND BLE. Does NCS2.8 currently support it?
I couldn't find a example program for ANT+in NCS2.8. How can I...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
