Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
Dear all,
We're developing a custom HW with several nRF52832 chips on one board. For convenience we applied third party module instead of building minimum system by ourselves...
Hello,
in our device we use the Timeslot API to share a 802.15.4 based protocol with BLE, softdevice is S140 6.1.1.
Problem: the 802.15.4 protocol misses appr 10% of the...
I'm having issues using the debugger on the nRF9160dk.
Here is the log that is output when I try to program the on-board 9160 with the command, nrfjprog --program <path_to...
Hello
I am trying to figure out the ram retention on my nRF52-DK using SES and SDK v17.1.0. I've run through the example ram_retention , and studied a topic in Nordic's...
Hi All,
My development IDE for BLE based firmware is Visual Studio Code.
SDK download for this version is 1.9.1 zephyr based.
I have select the example code "nrf/samples...
I'm using the nRF52832 with FreeRTOS and nRF5_SDK_17.0.2 on a custom board.
I am using a peripheral from a third party that uses Flash storage for certain parameters.
...
Hi Nordic,
I have 2 devices - nrf52840. One is Central and another is peripheral. I want to set a quicker data response time - shortest connection interval. As far as...
Hello,
as I see , many in DevZone have had a problem like this: we tried to merge twi-functionality into the basic ble_app_uart example. We set proper defines in sdk_config...
Hi,
we are developing a way to define through code a zigbee device composed of multiple endpoints, based on nRF5 SDK for Thread and Zigbee v4.1.0. The program can be flashed...
Hi all,
I'm trying to increase BLE throughput of ble_app_uart example (from official SDK16/ s132).
I've searched quite a few tutorials on which parameters should be...
Hi,
We need an detail description about uint32_t dev_config used in int i2c _configure ( const struct device * dev , uint32_t dev_config )
(zephyr i2c: https://docs...
Hello everyone.
I am beginner dev. I wanna run Serial Example Mesh and received data from BLE sensor. Can you support me complete this Project.
Thank you so much!
I'm testing a simple application based on the UDP/CoAP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi:
I want to use saadc peripheral,when i run the example "nRF5_SDK_17.0.2_d674dde\examples\peripheral\saadc",it worked well,but when I want to port this example to "nRF5_SDK_17...
