Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
Hello,
I am using the nRF52840 DK board and with Softdevice code nRF SDK 17.0.2. I am trying to write custom advertise data with custom type.
As you can see in the above...
Hi! Hope you are all doing well,
I'm having trouble making a project from scratch, I'm basically trying to filter bluetooth devices by manufacture code but I'm afraid that...
Hi All,
This has happened before so I know it's a handler error.
But this time I'm pretty sure my handle is not wrong, can help me?
in main.c =>
Best regards...
Hi,
Can you confirm the appropriate method to doing AFC correction for a GPS SNR test using the %XRFTEST command and then using the AFC correction result in the GPS SNR...
I use SPI to develop motion sensors KX022 and DW1000. The first digit of the received data is always 0xFF. If the first byte received is removed, it can be used normally....
I am trying BLE MESH light switch example with nRF5_SDK_for_Mesh_v5.0.0_src using nRF52833 DK. In the light switch example, server SDK is working fine and I can see the provisioning...
Hi All,
I am using Custom 128-bit UUID, My application need 3 Custom Services and 20 characteristics. But I need to make different Base for services and characteristic...
Hi,
I recently installed v1.9.0 SDK and while creating project from sample applications I am getting below error.
Attached is build logs from segger IDE.
Can anyone...
I'm looking to build a custom bootloader for my NRF52810 device. I'm developing on nrf sdk 17 with SD 112. I will be leveraging the secure bootloader example and re-using...
