Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I am evaluating if it is possible to use the nRF52840 PDM peripheral with a low-power microphone and I need a different CLK frequency setting than what is documented...
Hi,
I had used the NXP CLRC663 that need a EMC filter circuit to pass FCC part-15C certification.
nrf5340_NFC EVB havn't the circuit and it only have 2 parallel capacitors...
Hi there,
We are looking for the IAR startup code of the nrf5340 and nrf9160 devices. We have downloaded the MDK already, but only the GCC startup codes seems to be present...
I am using an iPhone Xs and trying to increase my transfer speed using the nrf connect app and a dvk-bl653 kit. I saw that my packets were only 27 bytes and I was only getting...
The nrf9160 tx power is 23DB ；
We is designing a procuct for ODM;
The size of product is small.
TRP requirements 20DB;
So the antenna designs is difficult；
Now my...
pc-nrfutil begins
#!/usr/bin/env python
Although is is not a good idea, the current beta of Mac OS does not contain /usr/bin/python.
This results in error: env:...
Hi,
I set up and testet the Low Power node example, described here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_lpn_README...
Hello People!
I need to transfer large amounts of information between our custom hardware based on the nRF52832 chip (S132+SDK17), and our custom mobile app running on a...
Hi,
in the .dts file，partitions is
Can it be changed to the following?
This modification does not compile .
What should be paid attention to when modifying,...
I am trying to implement bonding in central BLE uart_app example code but I don't know how to proceed as I'm a beginner . Do we need to make any changes at peripheral side...
Hello Nordic team!
I'm following this tutorial from Nordic to do DFU OTA: https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/getting...
I am following this post regarding reading the static MAC address for the nRF52840: https://devzone.nordicsemi.com/f/nordic-q-a/68376/trying-to-extract-the-static-mac-address...
Hi, we have a device that reads two sensors on separate i2c buses consecutively and transmits these using ble_nus_data_send().
The i2c sensors are read on an interrupt timer...
Hello all,
I am moving from the Arduino Uno to the nRF52 DK on Segger. A big difference
When looking at the examples, I cannot see the so-called setup() method, so, I...
