I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hii all,
i have a NRF52832 board with some sensors ..I coded it with SEGGER Embedded Studio . i Build and flashed and RUN successfully,
But after Disconnecting the board...
Hello , I am using the DTM in the NRF Connect.
Does you packet count preforms any CRC or other verification when receiving packets? I can not find any mention of BER (Bit...
Hello , I'm using nRF52832 DK and running the ble_app_multilink_central example . Here i want the list of beacons and get data from the specific beacon . I tried changing...
Hi, I am looking into combining SHT85 into Light lightness Server (mesh v4.2.0) code using nrf52840-DK. For my working SHT85 code, I am using an LCD to display the temperature...
Hello, this is Kwonjoon Lee. I have a problem of PC-BLE-Driver (C/C++ library) installation.
I am following installation guide which is written in the https://github.com...
Hi!
When reading the documentation of the I2S peripheral of the nRF52840, I don't see how to stop the transfer after the last data block. Figure 2 only shows how to start...
Hi,
I used the BLE blinky app on a nRF52832DK and it was working nicely.
I am then trying to make it run on a custom board with nRF52832QFAB version mounted.
I see several...
Hi,
I'm hoping someone can help me get faster throughput when doing DFU in nRF Connect Desktop
I'm using the following hardware / software:
- macOS 12.01
- nRF Connect...
On the nrf52840 I have libuarte working.
The part runs on 1Mbps with 2 timers connected in the define.
This all works great for 90% of the time.
When the incoming data...
Hello I'm curently working on a Project where I'm using the nrf52dk board with the nrf52832.
I wanted to change the dimension of the data transfered with my characteristics...
Hi, sdk:ncs v1.7.0
example path:D:\ncs\v1.7.0\zephyr\samples\subsys\usb\hid-cdc
board :nrf5340dk_nrf5340
DK:PCA10095
How to solve this problem?
Thank you for all...
Hi,
Excuse me. How can I modify cmakelist.exe to display file structure in segger Embedded Studio compiler? Now all files are app/libapp.a below. I have a lot of files now...
Hi, My system has 5 nRF52840 peripherals connected to one central device (PC app).
In the peripheral's sdk_config.h there is a macro NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1...
If download example light_switch on new clear chip nrf52832, that advertising is not done. But after downloading the firmware without mesh, example light_switch will broadcast...
