Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi!
When reading the documentation of the I2S peripheral of the nRF52840, I don't see how to stop the transfer after the last data block. Figure 2 only shows how to start...
Hi,
I used the BLE blinky app on a nRF52832DK and it was working nicely.
I am then trying to make it run on a custom board with nRF52832QFAB version mounted.
I see several...
Hi,
I'm hoping someone can help me get faster throughput when doing DFU in nRF Connect Desktop
I'm using the following hardware / software:
- macOS 12.01
- nRF Connect...
On the nrf52840 I have libuarte working.
The part runs on 1Mbps with 2 timers connected in the define.
This all works great for 90% of the time.
When the incoming data...
Hello I'm curently working on a Project where I'm using the nrf52dk board with the nrf52832.
I wanted to change the dimension of the data transfered with my characteristics...
Hi, sdk:ncs v1.7.0
example path:D:\ncs\v1.7.0\zephyr\samples\subsys\usb\hid-cdc
board :nrf5340dk_nrf5340
DK:PCA10095
How to solve this problem?
Thank you for all...
Hi,
Excuse me. How can I modify cmakelist.exe to display file structure in segger Embedded Studio compiler? Now all files are app/libapp.a below. I have a lot of files now...
Hi, My system has 5 nRF52840 peripherals connected to one central device (PC app).
In the peripheral's sdk_config.h there is a macro NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1...
If download example light_switch on new clear chip nrf52832, that advertising is not done. But after downloading the firmware without mesh, example light_switch will broadcast...
Hi All,
I am using VS code with nrf Connect Extension and nrf Connect SDK 1.7.0 develop nrf5340 application on windows10.
I created a new application from the Hello World...
I combined the BLE UART and SPIS Peripheral example of SDK V17.0.2 to receive 251 bytes of data from a microcontroller using SPIS protocol. The microcontroller sends data...
Hi,
Peripheral : SDK13, nRF52832
Central : SDK16, nRF52832
It is a phenomenon that occurs in the central device.
I have two questions about the secure connection...
I'm using the latest nRFConnect SDK w/ VSCode with a custom board connected to via a J-LINK. When I look at the call stack it only shows the current thread. I can see thread...
I would like to know when each BLE advertising event has ended for possibility stop after specific number of events and to be able to update advertising data between events...
Hi Dev Zone !
I am actually using nrf52840-dongle for wireless communication with the protocol Enhanced ShockBurst (ESB). I would like to connect an external antenna to...
