Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, we use nRF9160 and SDK 1.7.
in one of our applications, we need more than actually available flash. Now we have ~420kB for application - because we use MCUBoot and dual...
As title says, I cannot get anything to change in autoconf.h after changing the corresponding value in prj.conf using nRF Connect samples. I have tried both Project-->Reload...
I have made custom mobile app and I am trying to connect to it. When using nrf Connect app it is connecting properly
but i want to connect to my mobile app . it is connecting...
Hi, I'm trying to run the Openthread Cli sample on my nrf5340 DK, and it looks like that part is doing fine. But if I want to test the thread network with Putty I don't get...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi,
I'm trying to see how a BLE packet is formatted and sent from a Thingy:52 and I know the preloaded code on the THingy:52 has that functionality, can you direct me to...
Hi, do you have plans to test the nrf52805 at 105 degC or higher, similar to nrf51822 Extended Industrial Temperature range document
We will probably run the NRF52805 at...
I have created zigbee network using nordic dk board, i am trying to fetch all the active nodes in the network using zdo mgmt_lqi cli and i am getting those details but when...
Hi, What is in your opinion the best way to handle device reset after the Zigbee connection fails?
I want to archive behavior like so: after connection fails sleep for 10...
Hello,
I am working on a project which requires 2 FTDs and 2 MTDs (Sensor and Actuator) in a Thread Network.
We are using nRF52840 dongle as FTDs and arduino nano sense...
after connect v3.7.1 programer v1.4.11 for a nrf9160dk I get an error "Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: INVALID_OPERATION...
I have followed the tutorial of nRF5340: Network core bootloader to test the bootloader on app. core & net core.
I chose to use VS code to develop.
I am successful to...
Hi.
Simcom SIM7000 series datasheet recommends the following schematic:
Simcoms SIM800C module datasheet recommends the following schematic:
Quectel BG96 module...
I currently use an NRF52810 to write a firmware in an external flash, then an STM32 will read this firmware and download it in its internal flash. The communication between...
Hello,
I tried to read the value from bq4050 on smbus.
I had good results but I got wrong value randomly as following.
The last marked value is temperature from DAStatus2Reg...
