Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Howdy,
I'm evaluating the nRF Sniffer + nRF52840 dongle as a stop gap BLE sniffer solution, but I'm having a lot of issues setting it up.
Re: Installing nRF Sniffer (...
Good morning,
I am working with the AOA module of the nRF Connect SDK. I have been able to configure and program the transmitter with the CTE as well as the receiver and...
Dear Nordic,
we are developing an application based on SDK 17.0.2, it user FreeRTOS and BLE with Peer Manager.
We need to store few data in FLASH without confict with...
Hi
We are trying to get the DTM mode working for the NRF52 2nd BLE for testing BLE TX power and RSSI at the factory.
(1)HW setup is shown
(2 ) Procedure
We have...
Hello,
what are necessary that a Device automatically (without a 3rd party app) connect to the GATT Server with a HID Service.
I have implement a
HID Service,
Device...
hi，
I'm use nRF52840 to developing a Computer Keyboard，i wish 8X18 matrix a total of 144 buttons，About keyboard button matrix, please help to determine which GPIO can do...
Hello,
I am trying to resolve some compliance issues with the third-party libraries that are used in the SDK. For nanopb, it seems like the changes in pb_decode.h mentioned...
Hello,
I want to configure pin 0.13 as a rising edge interrupt.
Is there any sample code to configure the pin and interrupt handler?
Thanks in advance.
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
Hello; We want to use the GPS peripheral of nRF9160. Qorvo QM14501SR LNA is used in your evaluation board. QM14501SR is expensive for our project. Can we use LNA without band...
Hi,
i am working on nrf52832 . i am facing advertising issue with custom board. controller advertise only when i touch 32.786kHz crystals or two capacitors with my finger...
Hi,
I use example projects Thread: CoAP Client and Thread: CoAP Server . I can send and receive data over CoAP. My purpose is to use CoAP, CoAPS and UDP tohether. If client...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
Hello,
at the moment we are trying to realize a low power delay with the usage of the APP_TIMER.
We need a low power delay over 10 seconds.
This is our attempt:
...
