Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I am using nRF52810 Eval board for our project. I am using NRF toolbox UART function to control the PWM and UARTE function . I have tested PWM and UART separately with NRF...
Hello Everyone,
I am developing a Zigbee-based device using nRF52840.
So far all functionalities are working without any problem. Now for device load detection, we are...
Hi There,
I'm working with E-Ink display connected with nRF52 chip. I have a base library to display images and works very well.
Now I'm trying to use GFX library...
When creating my own project in Keil for the NRF51. I get this error when including files that include nrf.h. I do not have this problem in the example projects with the NRF51...
Hello, I've been trying to setup TWI with 3 sensors and so far I had no luck (custom board). Here's the situation: 1) 3 sensors are connected to nrf52820, SCL to P0.15, SDA...
I am a beginner who just received nRF52840 and working through Getting started with nRF Connect SDK (nRF52 Series). Everything worked fine until I got to chapter "Testing...
Hi all,
I have a wireless configuration that includes 5 peripheral devices (nRF52840 custom boards) and one central device (tablet) with a custom app.
All peripherals...
HI all,
Recenly, I am playing with nrf5340-DK to do some experiments. I read the datasheet of nrf5340 and found out that L31 is the pin for single-ended antenna connection...
Hello,
I received the Thingy not too long ago. Now that I've run some samples, it's time to use the NB network. I flash the AT_cmd sample. I open LTE Link Monitor to see...
I am designing a custom board for the NRF9160 following the 91 thingy as reference.
I will operate only in US and Canada. I noticed that multiple matching circuits have...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker, LTE with PSM, motion-activated GPS, using MQTT to send GPS location to backend.
prj...
We are trying to upload Bootloader only, but it fails with 'Error 5: FW version check failed'. Please view log / pictures.
We have tried to change the bootloader version...
Hello,
there is the following page:
https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library/blob/master/documentation.md
Known issues
Since iOS 13.3 (?)...
Hi all. I've seen a few posts about this, but none of them seem to have the knowledge I'm looking for. I am helping plan a device that has two units and will connect to a...
