Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Using SDK 17.0.2 and the nRF52840DK, I am setting up SPIM with a memory IC (not actually hooked up though, just looking at the signals on the oscilloscope). This code is executed...
I'm facing a problem with a product I'm developing. The problematic setup is as follows:
Two nRF52832 peripherals (S132 v6.0.0), each notifying on two characteristics...
Using: Windows Pro 10.0.19041 Build 19041
I'm trying to run Trace Collector for an issue with the nRF9160 and FOTA. I go to run the Trace Collector and it starts, but says...
I am using nRF52832. For reading ADC value for battery level percentage i have used 800k and 1M ressitor value. But while reading ADC Current cosumption is reached to 3 to...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
Documentation states that k_fifo_is_empty() returns 0 if data is available in the fifo (which is really implemented using a queue).
I'm receiving some spurious interrupts...
Hi,
In these conditions "custom device connected+bonded and whitelist enabled", when the device scan for beacons it see only the smartphone bonded to the device (don't see...
Hi! Looking at the product specifications V1.1 specifically 5.2.1 Electrical specification, one can see that on Sleep System On, full ram retention wake up on GPIOTE Port...
Hello,
I have following problem.
I use the nRF52840 DK and want to run it in nRF only mode, so I have the minimum power consumption. If I set the DK to low power mode...
Hi,
I encountered fota_evt_handler in azure_iot_hub.c is missing the call to azure_iot_hub_notify_event for the AZURE_FOTA_EVT_ERROR case, resulting in the application not...
I'm currently working with the MX25R6435F flash chip on board the nRF52840 DK and I'm running into issues with it. I don't know whether it's down to my lack of understanding...
Hello,
I am using nRF52832 integration. While drawing the PCB, I could not find the pin definitions in detail in the datasheet. Which pins correspond to SPI, I2C, and UART...
