I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
am use SPIM . I...
I have an issue in buttonless dfu,I have 2 kinds of device,one has issue in dfu,another one has buttonless dfu and works well, I transported DFU code form another kind of...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am in the process of RF certification.
I downloaded the example at "nRF5_SDK_16.0.0_98a08e2...
I tried in vain to connect my nRF51822 eval board with LIS3DH using SPI. Currently I am using the SPI example in PCA10001 with spi_master_init and spi_master_tx_rx function...
Is there an issue with my clock that's causing the BLE not to advertise? The debugger seems to an error on the gatt_params_init() function, which should mean its a RAM address...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
Hi,
I'm trying to implement Install Codes on our project without good results: The end device could not join the coordinator network after retrying several times.
Because...
Hi All,
I need to send HCI commands from my uC to nRF52840 (with DTM firmware) via UART to for example set channel, Tx power, packet type etc.
Are there any examples/documentation...
Hello,
nRF52832 BLE project using SDK 15.3.0 and SoftDevice 112 v6.1.1. Circuit has the output of a comparator connected to two GPIO pins (COMPARATOR_PIN1, COMPARATOR_PIN2...
Hey guys, I'm currently working with NRF9160, developing code that requires a work-item to be scheduled within a time-frame (timeout value) that could go up to >24-hrs. I...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...
Hello,
I am using nRF52840-pdk with Keil5 and nRF-go studio for development purpose.
I am facing an issue that after new firmware version upload from nRF-go studio to...
Hi everyone,
Currently, I was developing an application on top of Zephyr. I notice that NRF52 SDK provides library for MQTT-SN protocol. However, my application needs to...
Can the TCLK timeout be changed? I have a ZigBee device that joins and performs a key exchange but then is forced to leave the network 12 seconds later due to a TCLK timeout...
