Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I am currently developing my app with nRF52 DK and use the nRF52480 Dongle as a simulated sensor using the built-in server definition capabilities in nRF Connect for Desktop...
Hi.
I am looking for advice on which board may fit my purpose. My intended route as of right now is described at the bottom of this post. I have a door lock that has an...
Hi, I am using ANT Protocol in nRF52832 SES SDK17.0.2
Run the code in <Install folder>\examples\ant\ant_broadcast\tx file and i found that need to download the SDK file...
Hello I have an application which advertises permanently on the Bluetooth but I would like that under certain conditions, that they advertise another name. Can you tell me...
Hi everyone,
In the USBD example we use ENDPOINT IN 1 to comunicate (if a button is pressed) with the host the position of a mouse.
I modified this example, I don't need...
Dear Sir.
In my program 2 strings I need to protect when a new firmware is updated.
#define PROD_DATE "PROD_DATE_03_12-2020" #define IRON_NUMBER "IRON_1234567899999...
Hello,
In my application I use NRF52840 with SDK 16.0.0 and softdevice 7.0.1. I want to add ECDH algorithm to my project using ECDH example in the SDK, but nrf_crypto_ecc_key_pair_generate...
Hi there,
I'm presuming that, when using the s140 soft device (or any of the soft devices), I cannot change the output of VDD to anything and must assume 3V.
I have tried...
PWM frequency and PWM steps resolution are related, we increase one and the other decrease and vice versa, we want high PWM frequency so we have low flickering and we want...
Hi everyone, after months of working with the nRF52840 dongle I decided to buy the nRF52840 DK. I work with the ide SEGGER EMBEDDED STUDIO. I tried to get the blinky example...
Hello,
I can smoothly run the sensor server / client model. I know that I can setup the periodic publication period with the nRF Mesh mobile app and don't have a problem...
I want to configure 32bytes sensor measurement data in advertise manufacturer specific data as follows.
But does not work, please help me.
My environment as follows. ...
Is there demo for video transmission on PCA10056 DK?
it is just video transimission demo. just loopback is ok.
we are using nRF52840. is it possible？ or other platform...
Dear Mr/Mrs,
I am learning to develop an Android BLE apk. I use the nRF Connect apk and Android-nRF-Toolbox to connect with my BLE device.
nRF Connect connect to the BLE...
I have an found a problem where I find FDS has 2 pages labeled as swap, which results in loss of one of the data pages.
my configuration is 2 data pages and 1 swap page...
