Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
We have an application for using the 802.15.4 protocol with a nRf52840 and a Front End Module. We are looking for an approach to take for integrating the FEM control into...
Hi,
I'm trying to figure out if my device is suffering from errata 172.
* How can I know if I'm using Ble_LR125Kbit or Ble_LR500Kbit? * I'm trying to use the function...
To the kind attention of Nordic support team,
I would like to do a question that is not strictly related to Nordic, but I hope your expert can kindly give me an answer,...
Hello,
I am a student who tries to make a smart IoT project using nRF9160 DK and Arducam OV5642. I am searching on the internet to where to start, but I cannot find any...
If all you need is changing PHY, Tx power and Device Name in a standard nRF52840, do you need building a new bootloader from the scratch or the is a way to edit the standard...
Hello,
I'm experimenting with the nRF SDK for Mesh v3.2.0 and a nRF52832 DK, specific with the LPN example.
I want to enable BLE DFU support so I followed the instructions...
I am programming with SDK15.0. Then I use nRFgo studio to download the merged program to the DK board. But it reported a validation failure. So I tried to download softdevice...
I am building a project that is based on the custom service example https://github.com/bjornspockeli/custom_ble_service_example but I don't like how it advertises in a way...
Hi!
I am trying to test the Immediate Alert Client application example (ble_app_ias_c) from nRF5_SDK_15.0.0 on my nRF52832 based module. I want to understand how to test...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
