Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
our appliction need to using I2S worked at 96kHz sampling, and i find two parameters , MCK and the CONFIG.RATIO,but when i use this formulation:
LRCK = MCK /CONFIG...
Hello,
I think about connecting two central devices (nRF's 52840) using one common antenna. One device will be only RX and will scan for a advertisements, second will manage...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
I have setup the nRF52840 DK as below
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-setup-the-thread-demo-displayed-live-at-google-i-o
Setup WireShark...
Hi,
We are currently going to try and implement FOTA/DFU with an nRF52840 controller and an nrf52832 peripheral. Is there any example for how this can be accomplished...
Hi,
I currently have a nRF52840DK pre-programmed with the DFU over BLE, but with the debug version. I am unable to physically get to the device, if I wish to perform a...
Hello,
We are using the SPIS on the nRF52832. We are seeing a higher than expected consumption when it's enabled and not used.
I measure around 7uA extra when enabling...
Hi:
I test the system off mode, I attached a micro vibration sensor. Pulse generated when shaking as follow.
the button config is BSP example default(toggle) , i try to...
Hi,
I am testing the blue_app_uart example and I want to send data
from my smartphone uart terminal app,back to the nRF52840 DK,
Nothing is being received by the segger...
In the latest Mesh SDK, nodes are subscribed to a GROUP address. In previous versions - 2.0.0 I believe - you could also send to a predetermined node.
I am trying to figure...
Hi I am reviewing the nRF52840-DK hardware documentation to make boards with good antenna performance.
Q1. I have divided it into three areas as shown below. Is my understanding...
Hi,
I have been trying to use Keil MDK's Middleware File System with my application. However, when I try to set the Software Component under Manage Run-Time Environment...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi!
I am using the Segger embedded Studio with PCA10056 successfully. Now I have to evaluate LARD DVK-BL654 (because it has external antenna). I found a guide which says...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....