Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
I'm in the middle of developing a software that runs on nRF52840 and scans for BLE devices all of the time, then quickly connects to each and every one as fast as possible...
We're using a host PC to write factory calibration data to an nrf52 running SDK14.0.0 and S132. We're using a serial port, 115200 8N1, without hardware handshaking. The SD...
Hello,
very simple question:
each time i click on the link from the following page, I get an ACCESS DENIED error
infocenter.nordicsemi.com/index.jsp
I know that...
I made some changes in mesh light_switch_client example code and tried to build it in SES, it passed compiling, but stucked at linking:
Building ‘light_switch_client_nrf52832_xxAA_s132_6...
hi..
i merged the two programs twi sensor and uart ... successfully complied
but while debugging i am getting this error
while (m_xfer_done == false)
lm75_mode();...
Hello all,
I have a question about the SAADC of nRF52832.
Now I use the SAADC to measure the some external sensor voltage and the internal VDD voltage.
The sensor connection...
Hello, Excuse me! I used the LFRC,the calibration interval of which is 8s, in my application on NRF52832. In order to measure the power consumption,I want to know the duartion...
Hi,
As well know, nRF52832 can use "16Mhz base-clock to output PWM signal, and it is very simple to create 4Mhz, 2Mhz, 1MHz signal output,
But, If I want to output a...
I'm trying to get a stripped down, simple LED blinking sample to work (like blinky) when building with GCC however main() is never called. I'm guessing I'm either using the...
I'm trying to take a project we had working with only an application, no softdevice or bootloader, and add a bootloader and softdevice, with the application still not requiring...
I am working on nrf5_SDK_for_Mesh_v2.2.0 with nRF5_SDK_15.0.0 and softdevice 6.0.0. I run code on PCA10040 dev boards. I am trying use a timer to send onoff message from a...
Hi Nordic,
Does FDS affect PPI ADC acquisition when writing data? The test found that once the FDS is written to the data, the ADC data returned by the PPI ADC is fixed...
Hello Nordic experts,
I am working with nRF5_SDK_15.2.0_9412b96 SDK.
In example nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_hrs_freertos/main.c I have at line...
Hi all,
The setup that I am aiming for has a number of nodes, which will send the IMU data to a central base station. The communication is achieved using a bunch of nRF24L01...
I keep getting stuck in the TIMER1_IRQHandler function.
When I debug the code, I get to line 20 (exiting interrupt function scope) and then the assembly code hits a nop...
