Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
First proof-of-concept super-simple nRF51 board. When we load software onto this board, will we have to tailor or configure the software to bypass or disable any functionality...
Our application is similar to a wireless keyboard. The events are very sparse but we need low latency (~50ms). If I understood correctly, BLE is a synchronous protocol, meaning...
Hi I am working on nRF52832 using SDK15.02 i have below query:
During discovery I am connecting each device which is advertising and then discover for services offered by...
hi,
i am doing a project where i am using nrf52810 SOC which acts as ble shield for out customer.
customer's master device also has wifi connectivity.
the nrf52810 will...
Hi,
I had a meeting with one of our customers and was asked if any of Nordic products support ToF. I briefly looked through DevZone and found that it was not supported....
I have problem with BLE connection being constantly disconnected after 30 seconds. It is always disconnected by central device. It doesn't matter if it is iOS, Android or...
Hello,
I`m trying to run the example in the light_switch after i download the "nrf5SDKforMeshv310src"
When I tried to build Provisioner or Client ,for example this project...
Dears,
I have nRF9160-DK and nRF51-DK(PCA10028).
I have used nRFgo Studio with nRF51-DK(PCA10028) to firmware download.
And I have used nRF Connect - Bluetooth Low...
Hi.
How could I set extended advertising through the 37 secondary channels as default, in an nRF52840 module which is using PHY_CODED modulation and running a ble_app_uart...
When working on adapting the bootloader for NRF52832_XXAB I noticed that -DNRF52 seems to define NRF52832_XXAA and later defining -DNRF52832_XXAB does not override it. I suppose...
If the Mesh DFU process fails (maybe a packet gets dropped or something), what happens? Will the device get stuck in an unknown state? What does the recovery process look...
I am trying to make the nrf9160 device work with our own AWS IoT account.
The nrf9160 device succeeds to run mqtt_client_tls_connect(). Then it runs mqtt_client_tls_write...
Hello,
I am using SDK12.3 and have problem with garbage collection (FDS module).
My apllication depends on timeslot, so that FDS is supposed to run together with Bluetooth...
Hi
I am writing ANT+ device on pStorage and want to read back from memory during ANT+ stack init. I am trying to change the Device name on this snippet
No luck so...
