I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi
with SDK15 SD140 6.1.0. I'm trying to use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED with CODED physical.
I run the following code
and getting...
Hello Community,
The PCB project I'm working on is ready to be optimized for production. What I am concerned with today is the electromagnetic compliance of the PCB.
In...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
In my project I have to implement passkey or whitelist in the conection with...
Hi,
I'm trying to run the OTA DFU for the nrf52832 (sdk v14.2, softdevice v5.1) from multiple devices.
In the OTA script, I enabl the receipt notifications and it works...
I am working out of this MPU-twi example and am trying to validate sent data by printing it to the serial monitor. From what I've seen in SDK 15.1.0 examples, it seems like...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
Hi, I wrote the firmware in SDK 11 preview, and when migrating it to SDK 11 the NFC code does not work, also it seems when the NFC startup code is executed none of the GPIO...
Hi All,
I've not enough experience in nrf51822. I'm developing a battery powered device using the Nordic nrf51822 pca10028. I want to connect two nrf51822 pca10028 boards...
