Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
Hello,
I'm currently using an nRF9160 DK v.0.7.0 and the provided samples like the asset tracker and the at command client. Compiling, flashing etc. of the firmware already...
Dear Sir/Madam,
Can nRF Sniffer fetch the data of BT Classic Devices having any BT Version from BT 2.1 to BT 5.0?
Kindly help me on this issue
Regards,
MIHIR TAIL...
(running a mesh 2.1 sdk)
I am provisioning my nodes over serial and do not need the GATT Provisioning service. I need to access the GATT Proxy service to send mesh data...
I want to upgrade FW.
Android app has done. but only iOS encounter some problems.
First, I try to download nRF Toolbox on Github. result is DFU Service not found .
I...
Hi,
As per subject I am looking to implement hardware on-the-fly AES-CCM encryption/decryption of ESB packets. Are there any examples/guides available for the nRF52840?...
Hi,
With the PPK PCA63511 we have tried different PPK software such as python 1.1, nRF connect for desktop.
In that process we observed that current measurements are...
