Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
I am looking into interfacing a SD card to the nRF52840. I have used the FatFS example and that is working ok with SPI. Then I have looked at the QSPI example and that also...
Hello,
I am using sdk 12.2 and nrf52 dk.
I am storing some data in flash using ( sd_flash_write((uint32_t*)0x4F800,m_deadbeef, sizeof(m_deadbeef));) and I am able...
Hi
I got the problem to connect customer board(nRF52) via SWD.
My connection should be fine and customer board is also supplied 3,3V by external power.
How I wire 52Dk...
Hi,
I want to add fstorage functionality to my applikation. I added all the files and functions as in the fstorage example from Nordic, but I get a linker error that the...
I am using an RTC to periodically kick off a PWM pulse train. This all works beautifully, but draws far more current than expected. From what I've read, this is because the...
Hi,
I've been working to get a Ublox GPS module to interface with my NRF52840 DK over UART. The GPS device boots up and starts streaming data almost immediately.
I am...
I am nRF52832 , S132 , SDK15.0.0 // nRF52840, SDK15.0.0 is used.
Examples of esb_prx, esb_ptx are modified and used.
Transmitter : nRF52832
Receive : nRF52840_DK
Senders...
hello
I have once again issues when I want to write a 'long" characteristic e.g. 85 bytes.
1) if I use a smaller MTU e.g. 23 or 50, I received corrtectly the User Memory...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
