Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I am using the example ble central devices from the SDK 8.1. The example provided prints out to pin 19 (the on-board LED). I wanted to change the functionality to print to...
I am trying to add ADC to my program per the nordic examples on GitHub.
Using GCC, SDK12, nrf51.
These are the errors I am getting: (sorry for the formatting of this - code...
Hi,
SDK12 does not have Pstorage. I want to show you how to add it.
Steps:
Copy the pstorage folder in SDK11 into the SDK12 \components folder.
Open...
Hello,
I've been working on a project for some time now and prototyping it with replacement atmel ic's like the at mega328 and bluetooth modules and other stuff in the...
My custom board sometimes freezed on initialization process of bootloader (SDK11 dual_bank_ble_s130) when after long running and reconnect the power.
However the symptoms...
I am running the ble_app_hrs example and it runs as expected.
However, I tried removing one or more of the services from services_init as well as the corresponding advertisement...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
I am trying to add the spi and twi drivers to the ble_app_template project, but I keep running into errors. I am using the SDK 12.2.0. How are we supposed to go about adding...
Problem:
In our project we have one peripheral which can be bonded to many phones at the same time (of cause) while they are still close to it, thus connected via OS. ...
I am trying to scan and connect to a Polar H7 HR belt (which I can do), with m_scan_mode = BLE_NO_SCAN. Once this happens, I understand they are supposed to bond, and at that...
In my low-power application I need to use advertising interval of few seconds (two or more) in order to get lifetime of a year with CR2450 battery. However, the Android application...
There's a great application nRF UART 2.0 that can be used like a terminal with a Bluetooth LE device implementing the "Nordic UART" service. Now I would like to store output...
I am using a nrf52832 with SDK 11.0.0 and sd132. I need to add in-flash storage to my application so I'm looking at the NVMEM documentation and the pstorage module. I understand...
Dear Sir/ Madam,
I want your suggestions and recommendation regarding to choose which one of your BLE development kit.
I want a Bluetooth development kit which has long...
