Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi,
we integrated in a board design the one of the nRF51822 proposed by Nordic. It is written on the chip:
N51822
CEAAO1
1401AA
I can flash my board using...
I am writing a python app that uses the nRF51 dongle and the s130 SoftDevice. I need to pair with a peripheral that uses a fixed passkey. Is there a python implementation...
I'm trying to add authentication with a key acquired Out-of-Band to a Peripheral BLE device in which I already have non-MITM bonding working. I'm using the Peer Manager module...
Hi ,
Am using NRF52 ,S132 SoftDevice
I have a simple Question, How can I know is any device already bonded or not to my peripheral ??
I need to show an option "Delete...
I am using nordic_sdk_10 with nrf51822 USB Dongle. I did a eraseall
flashed my softdevice and dfu bootloader and did a reset. Now i can see advertisement report DFU_Targ...
I am using a custom board with NRF51822-QFAC-R7 and Master Control panel on Android. The DFU is working with test images from SDK130.
BL : examples/dfu/bootloader/hex/dfu_dual_bank_ble_s130_pca10028...
Hi all,
I have been trying to get my Nordic nRF51822 transmit continuously on a particular channel for FCC certification. The Test lab wants me to test the product in 2402MHz...
Dear Forum Users,
I am trying to send the data in a burst. Thanks to this post I have managed to achieve ~2,5 kB/s. However this lasts only for few seconds. Then the stream...
When i load the example radio_test pca10040 in Keil i get the following error messages
Error #544: Required Software Pack 'ARM.CMSIS.4.5.0' is not installed
Error #544:...
Hello
I plan to use two Bluefruit LE Micro devices that contain the nrf51822 as BLE beacons.
I also plan to use a BLE receiver (on another arduino) to receive the beacons...
Hi,
I'm using GCC with SDK11 on linux. I'm able to build successfully. When I try to run "make flash" or "make flash_softdevice", I get error nrfjprog command not found...
I just got the nrf51822 evaluation kit. I followed the instruction and installed everything per instruction. When I tried to open “Blinky” project, I am getting the following...
Hello,
I have a peripheral based on the nrf52 that connects to my Android phone already in direct advertisement mode.
I am trying to get a NRF52 central working with...