Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hello Nordic Team,
I am working on an application using the nRF52833 with the following requirements:
Device operates as both BLE Central + Peripheral
Stores bonding...
Hi,
I’m looking to program an external device that runs on 3.3V with my NRF52840 DK (v3.0.1), and I’m looking to verify that this is possible. I know that the DK runs at...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
Hello.
Are you able to give any specific details around an SDC Assertion with File ID 13 and Line 451 please?
The nRF Connect version is v3.2.4.
I'm trying to isolate...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
Hi，
Excuse me, does the current Mesh（NCS 3.2.4） support Directed Forwarding and Remote Provisioning? The examples in NCS 3.2.4 don’t seem to include configurations for the...
Hi, from documentation, When NPM1300 enter Hibernate Mode Buck1 Buck2 output will be turn offed.
But for my testing with nPM1300-EK board, when using nPM PowerUP v2.22 pc...
Hi all,
I'm hoping someone can explain a behavior I've observed. I have a workaround but I want to understand the mechanism.
Setup
nRF54L15, NCS v3.1.0
ICM-42670...
We are experiencing critical data integrity issues on the BLE link of our gateway device. The problem occurs specifically when the device is operating as a BLE-to-Wi-Fi bridge...
Summary
On NCS v3.3.0 with CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and a single Ethernet AIL interface (W5500), the Border Router never initialises:
ot br state → uninitialized...
NCS 3.1.0 (and newer), nRF9160/51
Some applications using "at_host", maybe together with "at_cmd_custom", would benefit from a possible filter before passing the at-cmds...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Hi,
I'm trying to install the nordic sdk/toolchain combo via nrfutil command line (Windows x64) and I get the following error:
Is there any known way to resolve this...
