Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi,
I've just realized the project from
https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers
And it is working quiet...
Hello everyone, I am trying to send and receive messages over UART using Teraterm, the PCA10059 dongle and the UART Android app.
I was following the directions found in...
When I was trying to update the modem firmware, it showed something like this...
Traceback (most recent call last): File "c:\python37\lib\runpy.py", line 193, in _run_module_as_main...
Hi,
I am working on increase data throughput between phone and nrf52832. I am using SDK 15.3.
I create a service and a notify characteristic. I am sending 20-byte packet...
I currently have a hobby product that reads sensors and turns on/off relays based on that sensor input. I've got an nRF52840 that sits on my sensors and relays, and I have...
Hi,
I am working on nRF52832 with MAX30205 temperature sensor , i am comparing the temperature with threshold value like this if (m_sample <threshold) then send the data...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
In my application, I am starting BLE advertisement...
Hi,
I'm trying to include AES256 CTR in the ble_app_template project.
What i've done so far: .c files:
- Included the files from /components/libraries/crypto
...
The time to first fix on the Development Board (as well as a prototype PCB I have made) are both around 2 minutes. After getting a fix, is any of the almanac or ephemeris...
Greetings. Is there a way to do information mapping using, for instance, one of the mesh nodes that could act as a client/provisioner to all other nodes and therefore keep...
Hi! I'm working with nRF52 development kit and SEGGER Embedded Studio. I was trying to modify the example given as ble_app_hids_mouse and take all the functions present in...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on System OFF mode.
1...
Hi, i am trying to add additional payload to the Mesh Light Switch example. However, i modified all structs and it came down to the status_handle() function inside generic_onoff_client...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
After wakeup from System OFF (due to GPIO event), I want to validate / debounce...
On the nrfCloud, when you clicked on a device (nrf9160DK), the previous version of the interface would show how much data was used of the "available" data associated with...
