Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
I installed SDK 15.3.0 build 59ac345 and started working though the DFU secure boot loader example. In the 15.3.0 documentation it says
Setup
You can find the source code...
Hello
We are using custom board which has two chip configuration for BLE stack. Main MCU runs the Zephyr Host only BT stack in peripheral mode.This is supposed to be GATT...
I am trying to compile the SPI example in SDK 15.2.0 for nrf52810. I am getting a compiler error in SES on nrfx_uart.c:
I modified the project according to the SDK documentation...
Dear all,
Is this possible to flip a switch on the board to get nRF9160 IOs at 3.3v rather than 1.8v ? I have a LoRa module that requires TTL 3.3v UART signals, and it...
Hello,
I believe I have found a possible race condition in experimental_task_manager / task_manager.c, task_events_wait().
The race occurs if a task calls task_events_wait...
Hello, I'm working with an example of ble_app_uart with SofDev132. I have modified the code a bit but I still use the nrf_pwr_mgmt_run function. The power consumption is 2...
hello, i am complete beginner to this field of MCU, i never worked on nordic MCUs. i am able to program the dk-board using the usb cable and readymade hex file provided in...
Hi,
I'd like to enable paring/bonding for a minute only when a button is pressed. So I need to disable pairing. I've learned that it should be done with
in "ble_evt_handler...
Hi,
I would like to have two different twi managers. One with TWI0 and one with TWI1. But if I try to enable them I get an error:
sdk_config.h:1810:22: error: unable to...
Hello,
I am new to BLE and trying to understand basic concepts.
Connection interval ranges from 7.5ms to 4sec. Device is doing Frequency hopping on all channels from...
Dear developers,
i now use the PPK intensively. I would like to have an additional feature. So far the trigger reacts only to exceeding a level. Would it be possible to...
I have developed CyclingPower SIG service based on (a) CSCS example and on (b) old file found here, at Devzone.
It used to work, but then something happened and I can't...
Hello.
I have been working with the nrf525840 dongle using SDK 15.2.0 trying to build a UART Service. I used the ble_app_uart example project that comes with the SDK and...
Hello everyone, I want to know and how, if it is possible, to hide UUID Beacon string during the advertising mode.
My goal is to not show the UUID by any sniffer, like Master...
Dear All,
I‘m going nuts while working on the basically really simpe task of reading ADC voltages on GPIO (AIN3) between 0 and 1.25V.
The voltage should fit well in...
