Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi everyone, I was wondering if it is possible to change clock frequency on n52832 manually. Datasheet (from n52832) says that it is automated distributed but do you know...
I have used online fds example code to store and read values from flash. I can store the data without any problem. I am storing static uint8_t array[8] = {1,2,3,4,5,6,7,8...
Hi,
3 years ago I buy the EK nrf51822. In this kit I have a card PCA10001 V2.1 and a dongle PCA10000 V2.1.
I would like to work on it today.
So i follow our quick start...
Hi there,
I'm trying to deploy mesh v0.9.1 alpha on my board, I've already run lightcontrol server and client on my nRF 52 DK, they work well.
Then I flash S130 v2.0.1 and...
Hello,
I've been using UART DFU feature quite extensively in one project which caused that I had to stick to SDK11 features (since bootloader relied on SD 132 2.0.0). ...
I couldn't see this in the documentation, but I might have missed it. Does the Logger Module consume additional power when it is enabled/initialised? If it does, presumably...
Hello,
I have developed a board with the integrated nRF51422 QFAA. I have the nRF51DK.
To compile I have used both mbed and arm-gcc and the binaries work perfectly on...
Hi everybody.
I am making a firmware based on ble_app_uart example (PCA10028 NRF51422, Softdevice S110, NRF51 SDK9.0). In this firmware, I insert dfu part ( follow by this...
I am testing out the Bluetooth Mesh SDK 0.9.1 Alpha using the light control client/server example. The examples have not been modified.
I have set up a nRF52 development...
In android while at the stage of scanning there is list of ssid ,i am getting print of scan_result but while trying to print the RSSI value,the result is 0 .Files i have changes...
With our custom board, I have implemented the battery service and it's working well. But the nus service is not shown up at all, the same initialization code as the official...
i use the nrf52832,s uarte. using the app_uart_fifo.c document. but i can only receive the max 256 bytes.the configuration is belows:
APP_UART_FIFO_INIT(&comm_params,
...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
