Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
Using this doc it says the SPI supports 16 bit frames. Is this true for the nrF51822 BLE Nano? I found that the mbed API does not support 16 bit frames doc . Can I...
Hello,
I tryed to find in Q&A something that can help me understand how it is possible to measure battery voltage with nRF52, but i am not sure i found the exact explanations...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
What hidden settings am I missing this time in the awful Segger studio ?
I get an error :
unknown type name class
When I compile with this new class called...
hello i am new to spi, i am doing project on 3 wire spi interface. I am using 3 wire interface as Sclk,ssn,MOSI pins only , I am not using MISO pin .I am tested spi example...
hello, I am working on nRF52 DK spi protocal.I am using AD9837 as slave.Here i am using 3 wire interfacing.I am connecting Sclk,ssn,MOSI pins olny & I am not connecting MISo...
what's the maximum data rate of nrf24l01+ (with ACK and without ACK) using 2 nrfs?
if i use 4 nrf24l01 two in tx side and two in rx side.what would be the maximum data...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
Hello all,
I need to program nRF52 via the SWD pins. I cannot use the nrfjprog or J-link or Segger etc. I have connected 3 wires to the nRF52 - SWCLK, SWDIO and GND.
...
Hello to all
I'm working in an application that needs to be completely power optimized. In this program the device works as a scanner that if it finds an specific device...
Hi, I am wondering about the pre-made PCB's available on ebay, with a nRF24L01+. At a cost of $1, and with various forum stories over the Internet referencing issues such...
I am using NRF51422 S130. I have a master SPI configuration set up, and not using Nordic spi drivers provided in the examples. I think my configuration is correct.
1- I...
Hi,
We started out developing an application using the SoftDevice 1.0.0-3 (from SDK 0.9.2). We now need to upgrade to SoftDevice 4.0.2 (included in SDK 13.0.0).
We already...
