I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I have been using the nRF7002 DK board; the nRF7002 uses the QSPI bus and the external NOR flash uses SPI.
The nRF WiFi driver's HAL and interface functions all require...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made:DFU procedure...
The nRF5340DK's are not programmable on my pc. I have no issues using nRF52DK and nRF52840DK. I have 3 different nRF5340DK's, they all have the same issue.
When I try nrfjprog...
Hi There,
We're new to Nordic and in the process of attempting to move our custom Xamarin application and boards over to use the nRF52832 and the nRF Connect SDK. Has anyone...
Hello,
I used two samples, application_update and SLM, to test and try updating the app from application_update to SLM. I first downloaded the firmware of application_update...
I would like to store context information for each connection, but with central and peripheral connections storing different information. Ideally, this is done in two separate...
hi support team,
we can see the slide in this link： /cfs-file/__key/communityserver-discussions-components-files/4/3201.Measuring_5F00_distance_5F00_with_5F00_Nordic_5F00_Distance_5F00_Toolbox_5F00_slides...
hello Nordic
we are working with nrf52832 and nrf52840 running with ncs v2.5.0 (waiting for v2.7.0 cause 2.6.0 have some issues with cmsis fft tables that prevent us from...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
I am working on an application where I am using 3 SAADC channels all with the same reference pin.
Upon startup, I will call app_sensor_init() to initialize my SAADC, timer...
