We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
what should i do to get the what should i do to get the thingy91 connected to LTE Network ? the SIM has been acitvited but i still cannot connect the Dk to the network.thingy91...
Hi, I am working with ncs 2.6.0 trying to implement some logs using the DiagnosticLogs cluster
But It looks to me like it is not impemented/supported yet.
For testing...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
I am using the Direct Test Mode sample as a starting point (samples\bluetooth\direct_test_mode). I am using NRF Connect SDK Toolchain v2.5.0 and NRF Connect SDK v2.5.0. I...
As far as I know, ppk2 is an eye-catching and open source power evaluation tool. I got the source code of the power profiler from github, and obtained the hardware design...
Hello,
With the CMakeLists file, is it possible to make an error during compilation if the SDK version is not the correct one?
Example: I am developing an application...
I'm trying to modify this bit-banging ws2812 gpio Zephy driver to run on an nrf9160 board. The problem is I can't mange to get consistent pulse timing using assembly instructions...
Hello
I have a problem setting up communication between a nRF9161 and a nRF52840.
I have a custom board with a nRf9161 and a nRF52840. These two are connected with 5 lines...
Hello, I'm using the nrf5340 and nrf Connect SDK 2.6.1. Currently the MCUBoot is immutable and the cpuapp image is encrypted (it contains IP and secrets). The MCUBoot is kept...
Hello,
I 'm updating from Zephyr 3 .2.99 to Zephyr 3 . 4.99 .
I attempted to add a main() function to my application . (Heretofore I have not been using a main() function...
hello I am designing a custom PCB using an nRF5340 and i have one nRF5340 audio dk with me and both are configured as a gateway and headset . i am facing an issue in pairing...
To do this by reusing the sample of nRF5340 Audio I am thinking of using it by editing the overlay file.
nRF5340 Audio has A/D linked to P0.24, Use P0.24 separately from...
When I tried to use the sd_ble_gatts_value_get() function and found no error but no corresponding value returned, I was sure I had the right value in my feature because it...
Hi,
I try to create a one-button minimal "smart watch" based on a small nRF52840 module (register button press) and a second nRF52840 'central station' (receiving and converting...
