Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I want to use nRF5340's GPIOTE and DPPI implementation, pull up PA_SWITCH_CTX_PIN when NRF_RADIO->EVENTS_RXREADY is triggered, and pull down PA_SWITCH_CTX_PIN when NRF_RADIO...
Hi guys,
I have an interesting idea - organize a network for realtime audio communication. Basically duplex Walkie-Talkie but using bluetooth headsets. I tried to use ESP32...
Hello everyone,
at the moment I am working on a BLE program which collects data from various sensors and passes it to a Central device. For the transmission the BLE NUS...
I am using ESB with dynamic payload lengths. When I use length 252, I am sending the alphabet repeating, and I can see that the data cuts off around position 30 and repeats...
Are there any known issues when using a nRF52840 and S140 6.0.0 soft device and trying to transmit at +8 dB? From our measurements is appears that +4dB does indeed increase...
Hello,
I am using the nRF 9160 DK board. I am trying to create simple thread in Zephyr.
but the thread it's not running.
this is the code:
I tried also the other...
I accidentally pressed "verified" on https://devzone.nordicsemi.com/f/nordic-q-a/91104/making-rand-work-on-nrf52-nrf53-with-nrf-connect-sdk when it wasn't and I don't seem...
I am testing my own mesh protocol based on 802.15.4 using the NRF52840 dongle.
The reported RSSI value from nrf_radio_rssi_sample_get() never goes below -89dbm.
On the...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
