I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
Dear all,
We're developing a custom HW with several nRF52832 chips on one board. For convenience we applied third party module instead of building minimum system by ourselves...
Hello,
in our device we use the Timeslot API to share a 802.15.4 based protocol with BLE, softdevice is S140 6.1.1.
Problem: the 802.15.4 protocol misses appr 10% of the...
I'm having issues using the debugger on the nRF9160dk.
Here is the log that is output when I try to program the on-board 9160 with the command, nrfjprog --program <path_to...
Hello
I am trying to figure out the ram retention on my nRF52-DK using SES and SDK v17.1.0. I've run through the example ram_retention , and studied a topic in Nordic's...
Hi All,
My development IDE for BLE based firmware is Visual Studio Code.
SDK download for this version is 1.9.1 zephyr based.
I have select the example code "nrf/samples...
I'm using the nRF52832 with FreeRTOS and nRF5_SDK_17.0.2 on a custom board.
I am using a peripheral from a third party that uses Flash storage for certain parameters.
...
Hi Nordic,
I have 2 devices - nrf52840. One is Central and another is peripheral. I want to set a quicker data response time - shortest connection interval. As far as...
Hello,
as I see , many in DevZone have had a problem like this: we tried to merge twi-functionality into the basic ble_app_uart example. We set proper defines in sdk_config...
Hi,
we are developing a way to define through code a zigbee device composed of multiple endpoints, based on nRF5 SDK for Thread and Zigbee v4.1.0. The program can be flashed...
Hi all,
I'm trying to increase BLE throughput of ble_app_uart example (from official SDK16/ s132).
I've searched quite a few tutorials on which parameters should be...
Hi,
We need an detail description about uint32_t dev_config used in int i2c _configure ( const struct device * dev , uint32_t dev_config )
(zephyr i2c: https://docs...
Hello everyone.
I am beginner dev. I wanna run Serial Example Mesh and received data from BLE sensor. Can you support me complete this Project.
Thank you so much!
I'm testing a simple application based on the UDP/CoAP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi:
I want to use saadc peripheral,when i run the example "nRF5_SDK_17.0.2_d674dde\examples\peripheral\saadc",it worked well,but when I want to port this example to "nRF5_SDK_17...
