Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I have an issue when I want to read an attribute from a toll to my nrf52840 device.
For exemple attribut 0 of cluster basic, if I forge a general read request for...
Hi,
I am in the process of porting an application from an nrf52 to an nrf51 due to availability issues. One problem I run into is that bluetooth events are handled in...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
I have checked out and built the iBeacon sample in zephyr (samples/bluetooth/ibeacon) for nrfconnect version 1.7.1. I tried building for both the nrf52840dongle and nrf52dk_nrf52832...
Hi,
I have a custom 9160/mfw1.3.1 board with a set of matching networks and I need to setup MAGPIO to control these. This will only be used for cellular, not for GPS.
...
Hello,
We have produced a product that uses the 82520 chip. This product uses the NUS service. We want the Windows PC to use its built-in Bluetooth to connect...
Hello,
I need a PMIC for a lithium polymer rechargeable battery solution.
The nPM1100 from Nordic is interesting, but I see there is a cap on the output current available...
I cannot get the blinky example to work with my NRF52 development kit. I used the example in the pca10040/blank/ses folder and it worked fine. I then modified the code per...
