Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
We have an existing application for the NRF52840 using SDKv15. This application will handle writing a new application to a free bank. I need to add the ability to jump from...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
I need to do a DFU via BLE but I do not have enough memory. For the past few months I have been working on a custom bootloader that would use an external memory to do the...
Hello, I am on conenct SDK 2.6.0 and trying to run the Zephyr Bluetooth:Central example on the nrf5340 dk to connect to a Minew S4 door sensor and get data from it. Here is...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi, I am working on using nrf7002dk to connect to AWS over WiFi. So far I have been able to connect to WiFi and send a HTTP get request through DHCPV4. When I continue to...
I am trying to get provisioning by trusted user procedure of aws_iot working by making some changes in aws_iot nrf sample
I have tested it with permanent certificates and...
In my nrf connect sdk projects i have external custom driver modules that i use across various projects to simplify code reuse. The issue i am having is that when I add MCUBOOT...
I am trying to use the the cellular monitor to get the device information but it seems like it does not connect to the device via J-Link, this is not a DK but a custom board...
I'm using an STA+AP configuration as well as monitor mode with a custom nrf7002 driver, which currently is working in a basic sense. I have however ran into issues regarding...
Good day
I have a lwm2m client running on a custom nrf9160 board. I would like to run everything network related to network on a separate chip. Assuming that the two chips...
I'm trying to connect to my Xiaomi Band 8 and read heart rate data using gatttool with the help of extended Bluetooth adaptor, UB500 | Bluetooth 5.0 Nano USB Adapter - TP...
Hi, I am trying to add some unit testing in my NRF Connect SDK based project. I am using Unity + CMock suggested here . For files with no complicated dependencies it works...
Dear Nordic
hardware:NRF5340, sdk:2.6.1
Our project needs to use floating-point calculations. Attempting to add CONFIG_FPU=y and CONFIG_FPU_SHARING=y to prj.conf will...