I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I'm working on a custom board with a nRF52833.
A small external battery is on the board, and when the power is off, 32.768khz of low power remains on the battery...
I'm running the SDK 17 radio test example on two nRF52840 DKs. My goal is to do a PER measurement in 802.15.4 -mode.
I configure the boards to use ieee802154_250Kbit mode...
Hi, I am using nrf52832 board. I was trying to disable the GPIOTE interrupt for a particular event (Event4) using INTENCLR register. My code was NRF_GPIOTE->INTENCLR = 1 ...
I am trying to get the nRF9160 DK power consumption down as much as possible to establish a baseline for development. After struggling to achieve the values claimed in the...
Hello,
I am using NCS v1.5.0 and an nRF9160 on a custom board, my application has a custom SPM and the secondary slot for the firmware image upgrade is stored on an external...
Hi,
I'm developing a peripheral sensor and central receiver as a complete set. So I wish the peripheral is only visible(or connectable) to its central device.
I know the...
Hi there!
I wanted to do a little side project that's something completely different than BLE Mesh (which I do for work). I decided Zigbee would be fun. Even more so because...
Hi,
I have an nRF52840 DevKit and dongle and am using SDK for mesh v.5 with SDK 17.0.2.
I want to update the firmware in a mesh network and am working on the mesh DFU...
I am using nRF52832 S132 V7.2.0. I am using ble_app_hrs_c example.
I only set nrf_ble_scan_filters_enable(&s_scan, NRF_BLE_SCAN_NAME_FILTER, true) to scan and match successfully...
Hi,
I am interfacing the Peripheral_hids_keyboard + peripheral_uart code
I code can print all the log info data printk and printf data in uart console
I want to separate...
Hi,
I've been working on the hrs example for nRF52840 DK and I wanted to add buttons to the project. For the first button (I took from app_blinky), it is working perfectly...
Hi,
I got a problem while updating BL using ble OTA DFU.
in NRFConnect App log it is showing as follows
nRF Connect, 2021-07-02
DfuTarg (E3:62:FA:A7:AB:D7)
V 17:09...
Hi All,
We've build multiple applications based on Thread. Now, with time our applications are getting bigger and complex, so we decided to integrate FreeRTOS into our applications...
