Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
While following the steps required to provision the nRF9160 Connect for Cloud certificate, I entered the 'AT+CFUN=4' in the AT command text field and I clicked 'Send' but...
I have a working code using SoftDevice 140 7.2.0 and Segger ES on the nRF52840 DK. I made the single adjustment of the preprocessor variable BOARD_PCA10056 to BOARD_PCA10059...
Hi,
I use example projects from Nordic Thread: CoAP Client and Thread: CoAP Server with Segger Studio Nordic Edition (projects use Zephry which is generated by NRFConnect...
Hello! I`m developing custom board with NRF52832-QFAA on board and need to use serial bootloader. As in example (secure_dfu_ble_s132_pca10040), I`ve implemented it on board...
Peripheral doesn't have any user interface that can be used for pairing and bonding but I want for my application is that the peripheral gets paired or bonded to the central...
I want to make one mesh beacon as a node of mesh network.
If one mesh beacon is a node of mesh network, I want the beacon broadcast the messages which in mesh network to...
I build some test project in Zephyr examples folder. (ncs\v1.5.1\zephyr\samples\basic\ND_test).
In additional I did some changes in the Zephyr project in drivers and added...
I have recntly purchased a Nordic Semiconductors nrf52840 development board. I am having issues with the J Link OB MSD. When connected to LINUX Ubuntu 20.04 LTS which is running...
Hi,
I am working on a bootloader that can do DFU for my nrf52840 DK. Currently, when the bootloader goes into DFU mode, it obtains the init packet via UART. Then, after...
Hi,
I'm trying to add the secure BLE bootloader(non debug, modified to run with S113, SDK 17.0.2) on a custom board with a nRF52810. I tried to DFU my main application(APP...
i working nrf52832 sdk 16 in that i want to use two uart?
actually nrf52832 have only one hardware interfced UART.but i try to implement two UART1 and UART2 in same program...
