Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi All,
I am using nRF52833 to make a Thread end device, and encountered a problem with the Thread network configuration in NCS. I want the device to connect to the Thread...
Dear Nordic expert,
I'm using nRF52840 as central with SDK 16.0.0.
I establish a connection with a peripheral (phone) and then I need to drop the connection. I set a timer...
Hi, everyone on the community
When using the BLE_APP_UART example, the serial port sends a packet of data to the mobile phone every 10ms, resulting in the device disconnecting...
I want to have a very stripped down version of the cat-tracker-app that just deals with settings, so I can import what is useful to an existing web application. I am new to...
I have succesfully got extended advertising working using the nRF SDK on the nRF52 DK, however I haven't been able to assign it a 128 bit service guid.
Setup:
The device...
Hi,
I want to add DFU to our board running SDK11 S130 but facing some problems.
I followed the instructions on infocenter, and started with ble_app_hrs example (from here...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
Hi All, I try to run the example GFX in sdk 17.02.
I wired the TFT :
---VCC ------------------ +3V ---GND ------------------ GND ---CS -------------------- P1.09 --...
Hello ,
NRF52840
sdk 15.2
In my application using ble central example in nrf52840 , i am able to write data in led characteristics and getting notification on HVX using...
Hi, I have tried to add support for BOS descriptor by appending a custom class generated from the Dummy example. The "main" class is the HID generic class, but with the NRF...
Hello
I only used PWM_library, but this is my first time using PWM_driver. Simply controlling the duty cycle of multiple channels has been successful, but I am not sure...
A little backgroud for my project. The goal of the project is to be able to identify the proximity of beaconing devices in an area to a specific observer which then reports...
Hi, Below is the mapping of RAM on the 840 from the infocenter. We want to utilize the functionality to turn off unused RAM (via sd_power_ram_power_clr), but we see that if...
I am using SoftDevice s140v6.1.1. The behavior is I was able to program nRF52840 through JTAG without any issue. I am checking out the OTA firmware update feature and nRFConnect...
Hello Everyone,
I am developing one product using nRF52840 MCU, in this project my master controller is nRF52840 MCU and the host is STM-based MCU.
My goal is to make...
