Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I have two questions:
1) I'm making a custom board for a hobby project! Are there any limitations to running a SPI driver with a voltage high of 1.8V? It seems that...
So I am using ESB and want a very percise timer. Because the 16mhz clock is not 2^n we want it to roll over at a certain value that is a multiple of 16mhz, so we chose 4.096E9...
Hi, I would like to add LED animation when DFU is in place. I know where to start it and where to stop it in the secure_bootloader source. The main issue for me is to add...
hello,
i am using nrf52840 with coded phy in our customised board and using the long range example as base for my application i have changed the ble_app_blinky to act as...
I find that you have a NRF_CLI_USES_TASK_MANAGER_ENABLED Macro. But it uses your own task frame. our project want a example using FreeRTOS with complete CLI function, thanks...
I have recently updated from SDK 1.4.2 to 1.5.0 on an nRF5340-DK
I have an application with a custom ble service. Most of the services have authentication permission requirements...
Hi,
I use the app_buton module to handle the buttons. When detecting a button interrupt I call a function that sends data to I2S (using the "app_sched_event_put" function...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
I'm new to the nRF connect sdk (but have used the previous sdk in the past), and am wondering what the best way to start a new project is? With the old sdk, it was easiest...
Hi,
I'm having "SOFTDEVICE: ASSERTION FAILED" when I set a breakpoint or pause the program to check some variables. That's really annoying, basically making the debugging...
Hi Dev team,
I was trying to build the mqtt_simple sample in the new NCS v1.5.0 and I am getting a build error.
I tried to build other samples as well but was faced...
Currently I am running one of the demo applications and have the nRF power source switch set to Vdd. The measured Vdd is 3.0V. Is it possible to change this to 3.3V? I would...
Hello
Is it posibile to do debug using Segger ES simulator for an example which uses also BLE stack?
More specific I am trying to debug the blinky example found in
...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
